NOTE:

All fasteners listed in this table can be reused after removal.

Application

Specification

Metric (English)

Driver or Passenger Seat Back Cushion Frame Bolt

35 N.m (26 lb ft)

Driver or Passenger Seat Bolt

45 N.m (33 lb ft)

Driver or Passenger Seat Inner Adjuster Front Finish Cover Fastener

2.5 N.m (22 lb in)

Front Seat Adjuster Handle Fastener

2.5 N.m (22 lb in)

Front Seat Belt Anchor Plate Tensioner Cover Fastener

2.5 N.m (22 lb in)

Front Seat Cushion Outer Finish Cover Fastener

2.5 N.m (22 lb in)

Front Seat Vertical Actuator Handle Fastener

2.5 N.m (22 lb in)

Front Seat Vertical Actuator Lever Fastener

2.5 N.m (22 lb in)

Rear Seat Armrest Bracket Fastener

3 N.m (27 lb in)

Rear Seat Armrest Fastener

3 N.m (27 lb in)

Rear Seat Back Bolster Fastener

9 N.m (80 lb in)

Rear Seat Back Cushion Hinge Fastener

45 N.m (33 lb ft)

Rear Seat Back Latch Fastener

45 N.m (33 lb ft)

Condition

Action

NOTE:

Replace all seat adjusters as an assembly. Replace both sides at

the same time.

The adjusters are not in parallel alignment with each other.

1. Loosen the floor pan attaching bolts.

2. Position the seat fully forward.

3. Tighten the bolts. Refer to Driver or Passenger Seat Removal and Installation.

Condition

Action

NOTE:

Replace all seat adjusters as an assembly. Replace both sides at the same time.

The adjusters are out of time.

Remove and reinstall the front bucket seat. Refer to Driver or Passenger Seat Removal and Installation.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedures

1. Disable SIR system. Refer to SIR Disabling and Enabling

2. Disconnect the seat belt from the tensioner. Refer to Front Seat Belt Retractor Replacement

1

Driver or Passenger Seat Bolt (Qty: 4)

CAUTION:

Refer to Fastener Caution .

Procedure

Adjust the seat to the full forward position to gain access to the rear bolts.

Tighten

45 N.m (33 lb ft)

Callout

Component Name

2

Driver or Passenger Seat

Procedure

1. Disconnect the electrical connector.

2. With the aid of an assistant, remove the front seat.

Callout

Component Name

Preliminary Procedure

Remove Driver or Passenger Seat. Refer to Driver or Passenger Seat Removal and Installation

1

Driver or Passenger Seat Inner Adjuster Front Finish Cover Fastener (Qty: 2)

CAUTION:

Refer to Fastener Caution .

Tighten

Callout

Component Name

2.5 N.m (22 lb in)

2

Driver or Passenger Seat Inner Adjuster Front Finish Cover

Procedure

Use a suitable tool to separate the seat inner adjuster front finish cover.

Callout

Component Name

Preliminary Procedure

Remove Driver or Passenger Seat Adjuster Handle. Refer to Driver or Passenger Seat Adjuster Handle Replacement

1

Front Seat Vertical Actuator Handle Cap

2

Front Seat Vertical Actuator Handle Fastener (Qty: 2)

CAUTION:

Refer to Fastener Caution .

Tighten

2.5 N.m (22 lb in)

Callout

Component Name

3

Driver or Passenger Seat Vertical Actuator Handle

Callout

Component Name

1

Front Seat Adjuster Finish Cover Bolt Cap

2

Front Seat Adjuster Handle Fastener

CAUTION:

Refer to Fastener Caution .

Tighten

2.5 N.m (22 lb in)

3

Front Seat Adjuster Handle

Callout

Component Name

1

Driver or Passenger Front Seat Head Restraint Guide Bezel (Qty: 2)

Procedure

1. Raise the headrest to gain access to the head restraint guide bezel.

2. Twist the bezel counter clockwise and push the bezel upward on the head restraint adjuster rod.

2

Driver or Passenger Seat Head Restraint Clip (Qty: 2)

Procedure

Using a suitable pointed or flat bladed tool, push the metal clip rearward while pulling upward on the head restraint.

3

Driver or Passenger Seat Head Restraint

Callout

Component Name

1

Front Seat Belt Anchor Plate Tensioner Cover Fastener

CAUTION:

Refer to Fastener Caution .

Tighten

2.5 N.m (22 lb in)

2

Front Seat Belt Anchor Plate Tensioner Cover

Procedure

Unclip and reposition the electrical harness from the seat belt anchor plate tensioner cover.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedures

1. Remove Driver or Passenger Seat. Refer to Driver or Passenger Seat Removal and Installation

2. Remove Front Seat Belt Anchor Plate Tensioner. Refer to Front Seat Belt Anchor Plate Tensioner Replacement

3. Remove Front Seat Belt Buckle. Refer to Front Seat Belt Buckle Replacement

4. Remove Front Seat Cushion Cover and Pad. Refer to Front Seat Cushion Cover and Pad Replacement

1

Driver or Passenger Seat Back Cushion Frame Bolt (Qty: 4)

CAUTION:

Refer to Fastener Caution .

Callout

Component Name

Tighten

35 N.m (26 lb ft)

2

Driver or Passenger Seat Cushion Frame

Procedure

1. Disconnect the electrical connector.

2. Transfer components as necessary.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedure Remove Front Seat Cushion Cover and Pad. Refer to Front Seat Cushion Cover and Pad Replacement

1

Front Seat Cushion Pad Support

Procedure

Disconnect and reposition harness as necessary.

Callout

Component Name

Preliminary Procedure

Remove Driver or Passenger Seat Adjuster Vertical Actuator Handle. Refer to Driver or Passenger Seat Adjuster Vertical Actuator Handle Replacement

1

Front Seat Cushion Outer Finish Cover Fastener (Qty: 3)

CAUTION:

Refer to Fastener Caution .

Tighten

2.5 N.m (22 lb in)

2

Front Seat Cushion Outer Finish Cover

Procedure

Squeeze retainer to release.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedures

1. Remove Driver or Passenger Seat. Refer to Driver or Passenger Seat Removal and Installation

2. Remove Driver or Passenger Seat Inner Adjuster Front Finish Cover. Refer to Driver or Passenger Seat Inner Adjuster Front Finish Cover Replacement

3. Remove Front Seat Cushion Outer Finish Cover. Refer to Front Seat Cushion Outer Finish Cover Replacement

1

Front Seat Cushion Cover

Procedure

1. Disengage the J-channel retainers from the seat cushion frame.

2. Disconnect the electrical connectors that attach to the seat cushion, if equipped.

3. Remove the seat cushion cover and pad from the seat cushion frame as an assembly.

4. Remove the hog rings and separate the seat cushion cover from the seat cushion pad by pulling the cover away from the pad.

Callout

Component Name

5. If servicing the passenger seat, re-zero the passenger presence system. Refer to

Passenger Presence System Rezeroing

2

Front Seat Cushion Heater

Install Front Seat Cushion Heater. Refer to Front Seat Cushion Heater Replacement

3

Front Seat Cushion Pad

Callout

Component Name

WARNING:

Refer to SIR Warning .

Procedure Remove Driver or Passenger Seat Back Cover and Pad. Refer to Driver or Passenger Seat Back Cover and Pad Replacement

1

Front Seat Cushion Pad Support

Callout

Component Name

WARNING:

Refer to SIR Warning .

WARNING:

Do not repair or replace the seat stitching or seams in the seat back trim cover with an internal mounted seat side airbag module.

Replace the complete seat back trim cover

Callout

Component Name

from the OEM. Non-

OEM seat stitching may cause improper airbag deployment which could result in personal injury.

Preliminary Procedures

1. Remove Driver or Passenger Seat. Refer to Driver or Passenger Seat Removal and Installation

2. Remove Driver or Passenger Seat Inner Adjuster Front Finish Cover. Refer to Driver or Passenger Seat Inner Adjuster Front Finish Cover Replacement

3. Remove Front Seat Cushion Outer Finish Cover. Refer to Front Seat Cushion Outer Finish Cover Replacement

4. Remove Driver or Passenger Seat Head Restraint. Refer to Driver or Passenger Seat Head Restraint Replacement

1

Driver or Passenger Seat Back Cushion Cover

Procedure

1. Disengage the j-channel retainers and tabs at the bottom of the seat back cover from the seat back cushion frame.

2. Disconnect the electrical connector that is attached to the seat back cushion, if equipped.

2

Front Seat Back Cushion Pad

Procedure

1. Remove the hog rings.

2. Separate the seat cover from the seat cushion pad by pulling the cover away from the pad.

3. Transfer the seat heater, if equipped.

NOTE:

Seat back cover can be damaged upon

Callout

Component Name

reinstalling cover to seat back pad.

When reinstalling the seat cushion cover to the seat pad, start in upper outboard corner and install outboard side of the cover. Then start at the upper inboard corner and install inboard side of cover.

Callout

Component Name

Preliminary Procedures

Remove Driver or Passenger Seat Back Cover and Pad. Refer to Driver or Passenger Seat Back Cover and Pad Replacement

1

Driver or Passenger Seat Back Cushion Pad Wire Rivet (Qty: 2)

WARNING:

Use the proper eye protection when drilling to prevent metal chips from causing physical injury.

Procedure

Drill out all of the rivets before removing the pad wire.

2

Driver or Passenger Seat Back Cushion Pad Wire

Procedure

When re-installing the cushion pad wire, re-rivet at the same location on the cushion frame with new rivets.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedures

1. Remove Driver or Passenger Seat. Refer to Driver or Passenger Seat Removal and Installation

2. Remove Driver or Passenger Seat Back Cover and Pad. Refer to Driver or Passenger Seat Back Cover and Pad Replacement

1

Driver or Passenger Seat Back Cushion Frame Bolt (Qty: 4)

CAUTION:

Refer to Fastener Caution .

Tighten

35 N.m (26 lb ft)

Callout

Component Name

2

Driver or Passenger Seat Back Cushion Frame

Procedure

1. Disconnect the electrical connector.

2. Transfer components as necessary.

Callout

Component Name

1

Rear Seat Armrest Cushion Cover

2

Rear Seat Armrest Fastener (Qty: 2)

CAUTION:

Refer to Fastener Caution .

Tighten

3 N.m (27 lb in)

Callout

Component Name

3

Rear Seat Armrest

Procedure

Release the retainer on the hinge bracket.

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Back Cushion Cover and Pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement (40%)Rear Seat Back Cushion Cover and Pad Replacement (60%)

1

Rear Seat Armrest Bracket Fastener (Qty: 2)

CAUTION:

Refer to Fastener Caution .

Tighten

3 N.m (27 lb in)

2

Rear Seat Armrest Bracket

Callout

Component Name

1

Rear Seat Head Restraint

Procedure

1. Lower the rear seat back forward to gain space between the head restraint and the roof.

2. Depress both buttons on the head restraint guides and pull upward to remove the head restraint from the seat.

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Head Restraint. Refer to Rear Seat Head Restraint Replacement

1

Rear Seat Head Restraint Guide (Qty: 2)

Procedure

Using a suitable flat-bladed tool, slide the tool on the inside of the guide until it finds the slot. Then push the tool forward pulling the guide tab inward, while pulling upward to remove the guide from the seat back frame.

Callout

Component Name

WARNING:

Refer to SIR Warning .

Preliminary Procedures

1. Disable SIR system. Refer to SIR Disabling and Enabling

2. Remove Rear Seat Cushion. Refer to Rear Seat Cushion Removal and Installation

1

Rear Seat Back Bolster Fastener

CAUTION:

Refer to Fastener Caution .

Tighten

9 N.m (80 lb in)

2

Rear Seat Back Bolster

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Cushion. Refer to Rear Seat Cushion Removal and Installation

1

Rear Seat Cushion Cover

Procedure

Remove the hog rings, disconnect the j-channel retainer, and remove the push-in retainers that secure the rear seat cushion cover to the pad.

2

Rear Seat Cushion Heater

Procedure

Disconnect all electrical connectors.

3

Rear Seat Cushion Pad

Callout

Component Name

1

Rear Seat Cushion

Procedure

1. Press inward on the two retainer tabs to release. These can be felt through a slot where the seat cushion cover meets the seat cushion pan.

2. Pull up on the front of the seat cushion and lift out of the vehicle.

3. {If equipped} Disconnect the electrical connectors.

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Cushion Cover and Pad. Refer to Rear Seat Cushion Cover and Pad Replacement

1

Rear Seat Cushion Frame

Procedure

Transfer components as necessary.

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Back Cushion Cover and Pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement (40%)Rear Seat Back Cushion Cover and Pad Replacement (60%)

1

Rear Seat Back Latch Fastener (Qty: 2)

CAUTION:

Refer to Fastener Caution .

Tighten

45 N.m (33 lb ft)

2

Rear Seat Latch

Callout

Component Name

Preliminary Procedures

1. Remove Rear Seat Back Bolster. Refer to Rear Seat Back Bolster Replacement

2. Remove the rear seat belt buckle nut. Refer to Rear Seat Belt Buckle Replacement

1

Rear Seat Back Cushion

Procedure

1. Pull the rear seat back cushion latch release located on the top of the rear seat back cushion, and fold the rear seat back cushion forward.

2. Push in on the rear seat back cushion pivot support, and release from bracket.

3. Pull up on the outer side of the rear seat back cushion and remove the rear seat back cushion from the bracket and hinge.

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Back Bolster. Refer to Rear Seat Back Bolster Replacement

1

Rear Seat Back Cushion Pivot Support

Procedure

1. Pull the rear seat back cushion latch release located on the top of the rear seat back cushion, and fold the rear seat back cushion forward.

2. Push in on the rear seat back cushion pivot support, and release from bracket.

2

Rear Seat Back Cushion

Procedure

Pull up on the outer side of the rear seat back cushion and remove the rear seat back cushion from the bracket and hinge.

Callout

Component Name

1

Rear Seat Belt Opening Cover

Procedure

1. Using a suitable flat-bladed tool, push inward on the rear tabs while pulling upward.

2. Position the belt through the slot in the opening cover slot.

Callout

Component Name

Preliminary Procedures

1. Remove Rear Seat Back Cushion. Refer to Rear Seat Back Cushion Removal and Installation (40%)

2. Remove Rear Seat Back Latch Release Handle Bezel. Refer to Rear Seat Back Latch Release Handle Bezel Replacement

3. Remove Rear Seat Head Restraint Guide. Refer to Rear Seat Head Restraint Guide Replacement

4. Remove Rear Seat Anchor Plate Bezel. Refer to Rear Seat Anchor Plate Bezel Replacement

1

Rear Seat Back Cushion Cover

Procedure

1. Remove the hog rings from the seat back pad.

2. Disconnect the J-channel from the seat back cushion frame.

3. Disconnect the electrical connector, if equipped with heated seat.

4. Remove the seat back cushion cover from the pad.

2

Rear Seat Support

Refer to Rear Seat Support Replacement

Callout

Component Name

3

Rear Seat Back Cushion Pad

Callout

Component Name

Preliminary Procedures

1. Remove Rear Seat Back Cushion. Refer to Rear Seat Back Cushion Removal and Installation (60%)

2. Remove Rear Seat Back Latch Release Handle Bezel. Refer to Rear Seat Back Latch Release Handle Bezel Replacement

3. Remove Rear Seat Belt Opening Cover. Refer to Rear Seat Belt Opening Cover Replacement

4. Remove Rear Seat Head Restraint Guide. Refer to Rear Seat Head Restraint Guide Replacement

5. Remove Rear Seat Armrest. Refer to Rear Seat Armrest Replacement

6. Remove Rear Seat Anchor Plate Bezel. Refer to Rear Seat Anchor Plate Bezel Replacement

1

Rear Seat Back Cushion Cover

Procedure

Callout

Component Name

1. Disconnect the J-channel from the seat back cushion frame.

2. Disconnect the electrical connector, if equipped with heated seat.

3. Remove the seat back cushion cover from the pad.

2

Rear Seat Support

Refer to Rear Seat Support Replacement

3

Rear Seat Back Cushion Pad

Callout

Component Name

Preliminary Procedure

Remove Rear Seat Back Cushion Cover and Pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement (40%)Rear Seat Back Cushion Cover and Pad Replacement (60%)

1

Rear Seat Back Cushion Frame

Procedure

Transfer components as necessary.

Callout

Component Name

Preliminary Procedures

1. Remove Rear Seat Back Cushion. Refer to Rear Seat Back Cushion Removal and Installation (60%)Rear Seat Back Cushion Removal and Installation (40%)

2. Remove Rear Compartment Floor Stowage Trim Compartment. Refer to Rear Compartment Floor Stowage Trim Compartment Replacement

1

Rear Seat Back Cushion Hinge Fastener (Qty: 3)

CAUTION:

Refer to Fastener Caution .

Tighten

45 N.m (33 lb ft)

2

Rear Seat Back Cushion Hinge

Procedure

Detach the rear seat back cushion hinge from the guide pin.

Callout

Component Name

Preliminary Procedure

Remove the seat back cover. Refer to Rear Seat Back Cushion Cover and Pad Replacement (40%)Rear Seat Back Cushion Cover and Pad Replacement (60%)

1

Rear Seat Support

Procedure

Release the rear seat anchor plate bezel using a suitable flat-bladed tool.

Callout

Component Name

1

Rear Seat Back Cushion Latch Release Handle Bezel

Procedure

Using a suitable flat-bladed tool, push inward on the rear tabs while pulling upward from the rear of the bezel to release it from the seat.

Callout

Component Name

1

Rear Seat Anchor Plate Bezel

Procedure

Release the rear seat anchor plate bezel using a suitable flat-bladed tool.